TECHNOLOGY FOR BACK PAIN

Ironman heavy duty
Try this for some relieve from joint compression

TECHNOLOGY FOR BACK PAIN

The exciting new technology we will cover here refers to easing back pain and sciatica that is caused by disc problems. In the United States it is estimated that about 7 million low back pain cases are related to disc problems. It is important to note that these new technologies are unproven, so it is imperative to use a healthy dose of caution. However, given that the treatment for disc problems are invasive surgeries, I felt it worthwhile to take a look at these new treatments because they are much less invasive, and they look quite promising.

Low back pain is one of the leading causes of lost work time, second only to the common cold. It affects 65-85% of the population of the United States at some point in their lives. The most common cause is a sprain, strain or spasm usually brought on by poor lifting technique, improper posture, bad back habits, or an unhealthy ergonomic environment. Another common cause is disc problems, brought on by injury, wear and tear or old age.

Other causes include a narrowing of the spinal or nerve canals, arthritic or degenerative changes in the small joints of the back, osteoporotic fractures, and sometimes even infections or tumors.Until now treatment options have been limited. Physical therapy can help to ease the painful muscles which struggle to cope with the spine problem, and PT can also help to prevent abnormal stresses on the spine.

Epidural steroid injections can reduce the inflammation in the general area and are often helpful, but the pain tends to recur if the underlying problem is severe. For acute problems the only remaining treatments have been to surgically remove part of the disc, or to surgically fuse the vertebrae to remove pressure on the disc.

Now there are some unproven minimally-invasive procedures available that may help with the treatment of back pain and sciatica known as Radiofrequency Discal Procedures among them is something called an Intradiscal  Biacuplast. Make sure you try everything available to you before considering surgery. I have something similar to Teeter hang-up I think it might help you its a little pricey but the construction is the best quality out there and is more comfortable for me.                                                                                                                                                                                                                                                       If you want one check it out here similar product to Teeter hand up← or try this less expensive one strong and heavy duty →Ironman←

Ironman heavy duty
Try this for some relieve from joint compression

I personally use this→1-KWAN-LOONG-oil← great aromatic oil, this is what the professional’s use when you go to a Massage Therapist. This oil is way better then Bio-freeze or Tiger balm with out a doubt and it’s way cheaper. Makes a great stocking stuffer this should be in every home.

3- KWAN-LOONG-OIL really does help relieve minor neck+back pain right away it soaks into the skin and last for hours, when you try →6-KWAN-LOONG-OIL← you will be wondering where has this been all these years. THANK YOU for reading if you have any question’s or request for content please send me an e-mail@ TALKINGABOUTPAIN1@GMAIL.COM  THANK YOU

 

About admin 15 Articles
hello , my name is mike I live in RI and been here my whole life never really ventured out other than a few state's like Maine,Texas,mass,conn,new jersey, Chicago that about it, I started tinkering around with small engines and just figure out how they come apart go back together and try to understand how they work. well it turn's from weed wacker's to lawn mower's to mini bike's then dirt bike's to on and off road motorcycle's then car engine's eventually truck's and diesel tow truck's, learned how to paint car's, so after wanting to get out of the fixing vehicles I moved on to learning about construction. started out as a laborer then apprentice to carpenter then finish carpenter, eventually I ended up with a good wood working company working to be better all the time and improve are skill's and ability to be the best. I was considered a perfectionist but really I was just doing whatever it took to make my work perfect like the way I'd want it if I was paying $50hr sometimes, just wanting the home owner to feel respect for their home and project. well I was the hardest worker out there put 125% in all the time and I'm not kidding I'd run circles around people but that did not get me anywhere yeah people knew me as a hard worker but that went down the drain in 2016 when I injured my back lifting 75-100lb garbage bag's down 3 flight's of stair's into a 30yd dumpster, ended up having a protruding disc pushing on the nerve which would lead me to surgery after that didn't help a reprovision surgery was done. I'm still having problem's everyday and the Doctor's want to put hardware in my spine screw's and a titanium cage to help keep the disc from pushing on the nerve and stop that from recurring, so I wanted to try and help other's in their own pain battle, thanks ,mike

Be the first to comment

Leave a Reply

Your email address will not be published.




This site uses Akismet to reduce spam. Learn how your comment data is processed.