RADIO FREQUENCY DISCAL PROCEDURES

Radio frequence discal probe

Radio frequency Discal Procedures

Nucleoplasty is a type of Radiofrequency Discal Procedure that involves inserting a very thin needle into the disc but instead of using a heating wire (as was previously done in a technique known as Intradiscal Electrothermoplasty, or IDET), a special radiofrequency probe is inserted through the needle into the disc. This probe generates a highly focused plasma field with enough energy to break up the molecular bonds of the gel in the nucleus, essentially vaporizing some of the nucleus.

The result is that 10-20% of the nucleus is removed which decompresses the disc and reduces the pressure both on the disc and the surrounding nerve roots. This technique may be beneficial for sciatica type of pain than the IDET, since nucleoplasty can actually reduce the disc bulge, which is pressing on a nerve root. The high-energy plasma field is actually generated at relatively low temperatures, so danger to surrounding tissues is minimized.

Another procedure called Intradiscal Biacuplasty (IDB) is an advanced type of radiofrequency ablation that also treats discs from the inside. It is currently the technique with the most interest—and recent support—in the research literature, but there is nevertheless concern about intradiscal procedures. Some research has shown that needle puncture of the disc can enhance and hasten disc degeneration however, the risk-benefit for these procedure is still unclear.

These new techniques are exciting. They offer the possibility of treating low back pain and sciatica with much less trauma and risk than surgery, but it’s important to remember that these are still unproven technologies. I’ll keep you posted on how research on these techniques develops, but it’s great that we have some new tools to help people with this often debilitating problem.

Spinal Pumps are called intrathecal  spinal pumps and can be used to deliver a continuous flow of pain relieving medication. Intrathecal refers to the fluid containing space that surrounds the spinal cord. The benefit of administering pain relieving medication through a spinal pump is that medications taken orally are diffused throughout the entire body. A spinal pump delivers pain-relieving medication precisely where it is needed.

(Ziconotide is a non-opiod medication that is now being used in spinal pumps and can be effective for treating a wide variety of chronic pain conditions, including sciatica. It is not an addictive medication.) This treatment is considered after standard conservative treatments have been ineffective or have caused intolerable side effects.

The pump is surgically implanted beneath the skin of the patient’s abdomen. A catheter is run to the level of the spine from where pain is transmitted. Medication is pumped directly into the spinal fluid allowing for a much more potent effect on the spinal cord. This drastically cuts down on the amount of medication needed and provides better pain relief with fewer side effects.

The pump is refilled every 1-3 months by inserting a needle through the skin and into a diaphragm on the surface of the pump. Several different medications can be administered this way. Since the system is beneath the skin, the risk of infection is minimized and the patient can be fully mobile and active.

Spinal Stimulators emit electrical pulses on the surface of the spinal cord to reduce pain. The stimulators are similar to pumps in that they are surgically implanted beneath the skin but differ in that electrical signals, rather than medication, are used to ease pain.

Electrical signals are passed through the tip of the catheter at the precise location near the involved segment of the spinal cord. The result is a tingling sensation, which eases pain. Current theory is that the electrical current input alters the spine’s processing of the pain so that the patient’s pain is reduced.

The patient is able to control the stimulator by holding a magnetic pulsing device over the skin on top of the implanted generator disk. The stimulator appears to be effective for patients with back and leg pain that spinal surgery did not relieve. There is data that shows that these patients will do better with the placement of a stimulator than they will with repeat surgery.

This approach is growing in use for chronic neck and back pain problems that have failed to respond to simpler treatments. New devices, such as the Neuro high frequency stimulator, are now available. These new devices may expand the utility and success of implanted stimulators for back pain. IF YOU WANT TO TRY A STIMUATOR TO RELEIVE YOUR PAIN TRY THIS  → TEN’S UNIT←

 

I personally use a →Ten’s/IF combo← to get the best relieve, You should only use your stimulator for 15-30mins max at any 1 time. I once used it for 1 hour consistently and the electrodes started to burn my skin. So make sure you only use it for short periods of time. Try getting larger electrodes if your pain area is more wide spread, also try using multi patches, Here are the→ 2×2 electrodes← they help target two separate area’s. You should get yourself extra electrodes pads, also different size’s even know their reusable sometimes you wish you might of bought 2 more. Here I found the→ larger electrodes 2X4 ←   THANK YOU for reading if you have any question’s or request for content please send me an e-mail@  TALKINGABOUTPAIN1@GMAIL.COM   THANK YOU 

About admin 15 Articles
hello , my name is mike I live in RI and been here my whole life never really ventured out other than a few state's like Maine,Texas,mass,conn,new jersey, Chicago that about it, I started tinkering around with small engines and just figure out how they come apart go back together and try to understand how they work. well it turn's from weed wacker's to lawn mower's to mini bike's then dirt bike's to on and off road motorcycle's then car engine's eventually truck's and diesel tow truck's, learned how to paint car's, so after wanting to get out of the fixing vehicles I moved on to learning about construction. started out as a laborer then apprentice to carpenter then finish carpenter, eventually I ended up with a good wood working company working to be better all the time and improve are skill's and ability to be the best. I was considered a perfectionist but really I was just doing whatever it took to make my work perfect like the way I'd want it if I was paying $50hr sometimes, just wanting the home owner to feel respect for their home and project. well I was the hardest worker out there put 125% in all the time and I'm not kidding I'd run circles around people but that did not get me anywhere yeah people knew me as a hard worker but that went down the drain in 2016 when I injured my back lifting 75-100lb garbage bag's down 3 flight's of stair's into a 30yd dumpster, ended up having a protruding disc pushing on the nerve which would lead me to surgery after that didn't help a reprovision surgery was done. I'm still having problem's everyday and the Doctor's want to put hardware in my spine screw's and a titanium cage to help keep the disc from pushing on the nerve and stop that from recurring, so I wanted to try and help other's in their own pain battle, thanks ,mike

Be the first to comment

Leave a Reply

Your email address will not be published.




This site uses Akismet to reduce spam. Learn how your comment data is processed.